Steel sections piled in the warehouse

Home  ›  Materials

Our
Materials.

A complete range of iron and steel solutions across bars, sections, tubes and flat products — held in depth rather than listed in a catalogue. If it is on this page, it is normally on the ground.

Ask for a Rate

  • 8product families
  • Fe 415–550DTMT grades
  • EN8–EN31alloy steels, tested
  • 1-Daydelivery on ready stock
Steel angles and channels racked in the yard

Angles & Channels

Structural frameworks & fabrication

A wide range of iron and steel angle and channel to meet the requirements of our customers. Skilled staff check each lot against industry quality parameters before final delivery, and we offer them at reasonable rates. Widely used in structural frames, transmission towers, sheds, trusses, platforms and general fabrication.

  • Angles — equal and unequal, 25×25 mm upward
  • Channels — ISMC, parallel flange and junior, 75 mm to 400 mm
  • Standard — IS 2062 / IS 808
Call Now
H and I section steel beams stacked by size

Beams & Girders

H/I beams for PEB & heavy structures

H and I section beams for pre-engineered buildings, industrial sheds, mezzanines and heavy structural work. Rolled at primary mills, held in the sections that actually move, and loaded under overhead cranes so a girder order does not wait on a rolling schedule.

  • Sections — ISMB, ISJB, ISWB and parallel-flange beams
  • Typical sizes — 100 mm to 600 mm
  • Standard — IS 2062 / IS 808
Call Now
MS pipes and hollow sections stacked in the yard

Pipes & Sections

MS pipes & hollow sections

We offer a wide range of MS pipes to meet the requirements of our customers. Skilled staff check these pipes against industry quality parameters before final delivery, and we offer them at reasonable rates. Supplied for structural, plumbing, scaffolding and general fabrication use.

  • Types — MS round pipe, GI pipe, square and rectangular hollow sections
  • Typical sizes — 15 NB to 250 NB; sections from 20×20 mm
  • Brands — including APL Apollo
Call Now
Hot rolled mild steel plates

MS Plates

Hot-rolled plates for industrial use

Hot rolled mild steel plate and sheet for industrial use, checked against industry quality parameters before final delivery and offered at reasonable rates. MS plates are versatile and widely used across industry for their strength and durability — in fabrication, tanks, structures, base plates and wear surfaces.

  • Types — HR plate and sheet, CR sheet, chequered plate
  • Typical thickness — 1.6 mm to 100 mm
  • Standard — IS 2062 grades
Call Now
Colour coated roofing sheets in red, blue and grey

Colour Coated Sheets

Roofing & cladding

Pre-painted colour coated sheet for roofing and cladding — warehouses, factory sheds, pre-engineered buildings and site structures. Supplied in the standard profiles and shades, cut to the lengths the job calls for.

  • Profiles — trapezoidal and corrugated roofing sheet
  • Typical thickness — 0.30 mm to 0.80 mm
  • Finish — standard roofing shades, colour coated both sides
  • Lengths — cut to size on request
Call Now
TMT reinforcement bars

TMT Bars

Construction & reinforcement

We offer a wide range of TMT bars approved by the Bureau of Indian Standards for building construction. They suit a variety of projects — bridges, dams and canals — and these TMT steel bars also find use in industrial power plants and their associated works. Delivery is made against the usual industry quality parameters, at reasonable rates.

  • Grades — Fe 415, Fe 500, Fe 500D, Fe 550, Fe 550D
  • Typical sizes — 8 mm to 32 mm
  • Standard — IS 1786, BIS approved
Call Now
Flat bars stacked by width

Flat Bars

Wide range for manufacturing

A wide range of flat bars for manufacturing, with rounds and squares held alongside them. Rolled flats, strips, squares and black and bright rounds for grillwork, gates, frames, base plates, machining and general fabrication — cut to the lengths you need.

  • Flats — 12 mm to 300 mm width
  • Squares — 10 mm to 100 mm
  • Rounds — black and bright, 8 mm to 150 mm diameter
  • Cutting — to required lengths on request
Call Now
Tested alloy steel rounds racked by grade

Alloy Steels

EN8, EN9, EN19, EN31

Tested alloy steel to meet the requirements of our customers. Skilled staff check the material against industry quality parameters before final delivery, and we offer it at reasonable rates. Supplied with test certificates for shafts, gears, pins, dies and machined components.

  • Grades — EN8, EN8D, EN9, EN19, EN31
  • Form — rounds, flats and squares
  • Documentation — mill test certificate on request
Call Now
  • MS
  • HC
  • Structural
  • Special Steels
  • Ready Stock

Why our range works.

From structural steel to industrial requirements — one dependable source.

Ready
Stock

Quality
Sourcing

Pan-India
Delivery

Fast
Dispatch

Sizes and grades move with the market.

The sizes listed here are indicative of what we normally carry. Rather than work from a fixed catalogue, send us the specification and quantity — we will confirm what is in the yard today, what can be arranged from the mill, and how quickly either can reach you.

Talk to Sales

Need a Size?

Tell us the section and grade.

Sizes and grades vary with stock. Send us what the drawing calls for and we will confirm availability, weight and price.

Please enter your name.
Enter a valid 10-digit Indian mobile number.
Enter a valid email address.
Tell us which material you need.

Or call +91 98737 29789 · +91 93110 29789
Or email mansaramsteel@gmail.com